plug  - Most  common, three pin Male, is actually a microphone jack used in professional sound production.

Connector Sold As Separate Part; See Connectors

Co-Axial plug (comes in two or three hole Female)

Connector Sold As Separate Part; See Connectors

Connector Sold As Separate Part; See Connectors

Mini Jack plug

Connector Sold As Separate Part; See Connectors

RCA jack (pretty much like a standard audio plug, except the outer skirt may be solid instead of four sections of plates

Connector Sold As Separate Part; See Connectors

Plug Switch Price:  $15.00

to have us change the connector to suit your needs.  A connector is nothing more than that.  Any 24V charger, for example, with the matching connector to your scooter or bike, will

Currie Technologies - XLR 3 Pin Chargers

Connector Sold As Separate Part; See Connectors

Pukka Compatible Co-axial 3 Pin

Charger 24V 2 amp 3 stage High quality charger from Gruber Power.    Features Smart Charger - Stops charging when pack is fully charged. Three stage float (stops charging gradually, essentially, like the float valve in your toilet).

NOW Only: $54.95 #Char3288 Shipping Add: $9.95 ($3.10 each additional)  - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted. Color: Black Delivery Issues? Product Insert - Go to Main Page

Charger 48v 3amp Monitor plug    Replacement for any 48V system, comes with Monitor Type Plug (or replace with your own).  Far too often manufacturers, while their own standards may be good, will select less than premium chargers to go with their scooters.  This can be disasterous!!  If a cheap charger goes bad, it's usually (from our experience) the cut-off circuit that fails, and that means that your battery pack, all four batteries, will more than likely be over-charged, causing them to physically swell up - at which point they are toast (and most likely smell like rotten eggs if it just happened to you). Signs of a cheap (and potentially dangerous) 48V charger are: NO FAN (This is particularly important as we get into the higher voltages.  The chargers become VERY HOT during operation and a simple fan can reduce the risk of thermal related failures, as well as house fires!) Simple design with minimal LED indicators. Rattles (bad soldering or securing of screws or other components) The bottom line is if your cheap charger fails, you not only replace the charger but all four of your now fried batteries!!  Can you afford not to replace that cheap charger now with our New Teking charger?  Features: Internal Fan for cool and efficient operation, as well as safety! Multiple LED Indicators let you know of problems with and the status of your charging. Input AC100-240V 50/60 HZ Output DC48V 3.0 AMP Smart Charger

SOT Price: $ 59.99 # Char3307  Shipping Add: $ 12.95 ($4.95 each additional)  - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted. Color: Grey  Delivery Issues? Product Insert - Go to Main Page

Connector Sold As Separate Part; See Connectors

Solar Chargers

Clamps - Universal

 1/4" Quick Connect Female Yellow

Features:

12-12 Gage Wire

Easy Crimp or Solder for more secure connection.

SOT Price: $1.20 (10 connectors)

#Conn3389

Shipping Add: $5.95 ($1.95 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color: Yellow

Product Insert - Go to Main Page

 1/4" Quick Connect Female Yellow

Features:

12-12 Gage Wire

Easy Crimp or Solder for more secure connection.

SOT Price: $1.20 (10 connectors)

#Conn3389

Shipping Add: $5.95 ($1.95 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color: Yellow

Product Insert - Go to Main Page

Connector Yellow Ring Terminal 5/16" Hole

Features

Quick Crimp ends

  For Larger nut secured battery terminals

  For 10 - 12 Gage wire used for supplying power to electric scooters and chairs.

SOT Price: $1.30 (Pack of 10)

#Con3359

Shipping Add: $4.95 ($1.00 each additional pack of 10) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Product Insert - Go to Main Page

 CONNECTOR 3 Pin Female In-Line XLR

Features:

Comes unassembled, just solder your leads (Pin 1 is usually positive - check with your meter first!) and assemble.

Strong Metal Casing.

Strong inner wire grip keeps the wire from coming out.

SOT Price: $4.99

#Con3276

Shipping Add: $5.95 ($1.50 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color:

Product Insert - Go to Main Page

 CONNECTOR 3 Pin Male In-Line XLR

Features:

Comes unassembled, just solder and assemble.

Strong Metal Casing

Strong inner wire grip keeps the wire from coming out

SOT Price: $5.95

#Con3277

Shipping Add: $5.95 ($1.50 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color:

Product Insert - Go to Main Page

 Connector 3-CONDUCTOR LOCKING CONNECTORS W/ LEADS

Features:

Mating pair of polarized multi-pin connectors with wire leads. Pins on 2.5mm centers. Black nylon housing with release on male side of connector. Female side of connector can be snap-mounted into a rectangular chassis mounting hole. 12" color-coded leads 22 AWG stranded wire on both connectors.

SOT Price: $2.69

#Conn3394

Shipping Add: $5.95 ($1.50 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color: Black Plastic

Product Insert - Go to Main Page

 Connector 6 CONDUCTOR CONNECTOR

Features:

Male / female ends connected with 10" wires. 6 conductors.

SOT Price: $5.39

#Conn3395

Shipping Add: $5.95 ($1.50 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color: Red/Black w/ White Housing

Product Insert - Go to Main Page

 4-CONDUCTOR LOCKING CONNECTORS W/LEADS

Features:

Mating pair of polarized multi-pin connectors with wire leads. Pins on 2.5mm centers. Black nylon housing with release on male side of connector. Female side of connector can be snap-mounted into a rectangular chassis mounting hole. 12" color-coded leads 22 AWG stranded wire on both connectors.

SOT Price: $3.25

#Conn3396

Shipping Add: $5.95 ($1.50 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color: Black Housing

Product Insert - Go to Main Page

Controller Currie Technologies 24V 40 amp SD-150-1

Currie's highest Amp Controller available.  Use this to step up the top speed (within the law for your area) on your older 24V 450/600 watt scooters with 3 pin Hall Effect throttle connectors.

For use with Brushed Motors Only.

Use with Currie Throttles SD-204 / SD-204-1 / SD-204-R / SD-203.

SOT Price: $39.98

#Cont3387

Shipping Add: $9.95 ($2.50 each additional) - Estimated Maximum, your actual shipping will be calculated, by weight, at check-out, multiple items discounted.

Color: Silver Heat Sink Aluminum Case

Delivery Issues?

Product Insert - Go to Main Page

Controller Currie Technologies 24V, 30Amp - Finned controller

Discontinued - Currie recommends you switch to the more standard 5-pin controller/throttle.  Please use a 5 pin controller and switch throttle to 5 pin to match.  Now you never have problems getting the outdated and limited production 6 pin controller or throttle.SD-125-3 2004 and earlier models electric scooters.  This is compatible with three pin Hall Effect throttle connector, for throttles shown below.

For use with Brushed Motors Only.

Compatible with throttles:

SOT Price: $39.98

#Con3047 - Discontinued

Shipping Add: $9.95 ($3.50 each additional) - Estimated Maximum, your actual shipping will be calculated, by weight, at check-out, multiple items discounted.

Color: Black

Product Insert - Go to Main Page

 Controller Currie Technologies 25A 24V Diagnostic

Controller Currie Technologies Diagnostic 25A 24V '06 500 Series SD-125-6, One flat black 6 pin clip Hall Effect throttle connector.

 For use with Brushed Motors Only.

Compatible with throttles:

SD-205-6 / SD-205 / SD-205-R

SOT Price: $32.95

#Cont3226

Shipping Add: $9.95 ($3.50 each additional) - Estimated Maximum, your actual shipping will be calculated, by weight, at check-out, multiple items discounted.

Color: Black

Delivery Issues?

Product Insert - Go to Main Page

Controller 36V 30A (6Pin)

 

Discontinued - Currie recommends you switch to the more standard 5-pin controller/throttle.  Please use a 5 pin controller and switch throttle to 5 pin to match.  Now you never have problems getting the outdated and limited production 6 pin controller or throttle.

Controller 36V 30A for Currie Schwinn, GT, or Mongoose scooter 36V with 6 pin throttle (hall effect throttle only, twist grip or thumb, addl. lines for LED and Diag.).  Can replace older 25 amp models and gain improved performance.

 Features:

  30 amp output for increased performance.

  Aluminum housing for cool operation

  Weatherproofed circuit board (epoxy resin)

  Connections:

•  Input: Weatherized Black connector with two wires - black and red

• Output: White connector with two heavy gage wires - blue and green

• Throttle Input: Flat Black plastic connector with six wires - red, yellow, green, blue, black, and purple

• Smaller White connector with red and black 

SOT Price: $0.00

#Cont3242 - Discontinued

Shipping Add: $0.00 ($0.00 each additional)  - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color: Silver

Delivery Issues?

Product Insert - Go to Main Page

  Controller 36V with Brake/turn/lights

Generic Scooter Controller for Brushed Motors.  Circuit Board ONLY - use with your Case/Heat Sink to replace your existing board, or use for experimentation.

Please NOTE: the throttle connection is labeled "de-raileur" on the controller.

Features:

36V Capacity (doubt will work with 24V due to Low Voltage Cut-off)

Simple, open board is great for lab/experimenting with motor controllers

Heavy gage "white" connectors, all labeled for easy connecting

SOT Price: $30.00

#ContU017

Shipping Add: $9.95 ($3.50 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color:

Delivery Issues?

Product Insert - Go to Main Page

  Single Speed Freewheel

Single Speed Freewheel

Features:

Spin on threads - fits Crystalyte Rear Hub Motors

Non-destructive removal

NOW Only: $10.43

#CL2920

Shipping Add: $8.95 ($3.50 each additional)

Delivery Issues?

Product Insert - Go to Main Page

  3 speed Freewheel

3 speed Freewheel

Features:

Spin on threads - fits Crystalyte Rear Hub Motors

Non-destructive removal

NOW Only: $17.95

#CL2954

Shipping Add: $8.95 ($3.50 each additional)

Delivery Issues?

Product Insert - Go to Main Page

 Weatherproof ATC Blade Type - Fuse Holder

Inline Blade or "wafer" fuse type holder.  Heavy gage wire allows for up to 40Amp fuse

Features:

Durable rubberized housing.

Simply snip looped wire and install in the line from your batteries to controller.

14 AWG wire.

SOT Price: $3.50

#Fuse3275

Shipping Add: $5.95 ($1.50 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color: Black (red wire)

Product Insert - Go to Main Page

 Fuse 15 AMP Blade

15 amp teal ATC automotive blade fuuse. 3/4" X 1/8". Fits fuseholder FHP-22. Used in many current model automobiles.

SOT Price: $2.00 Pack of 5

#Fuse3278

Shipping Add: $5.95 ($.25 each additional) - Estimated Maximum, your actual shipping will be calculated at check-out, multiple items discounted.

Color: Blue

Product Insert - Go to Main Page